Bruker manual MAKITA DES380

[. . . ] For this reason use the top edge of the bar whenever possible. When transporting the electric chain saw over long distances the power supply plug must be pulled out and the bar protection cover, included in the delivery, must be applied (20). For storing the electric chain saw over a long period of time or shipping it the oil tank must be completely emptied. [. . . ] If your skin repeatedly comes in contact with these substances for a longer period of time, it will desiccate. Before operating the saw for the first time, the oil feed system must be completely filled, until the chain oil lubricates the chain and guide bar. Note: After the saw has been turned off it is normal for residual chain oil to drip from the oil feed system, the guide bar and the chain for a time. Important note on bio-degradable chain oils: If you are not planning to use the saw again for an extended period of time, empty the oil tank and put in a small amount of regular engine oil (SAE 30), and then run the saw for a time. This is necessary to flush out all remaining bio-degradable oil from the oil tank, oil-feed system, chain and guide bar, as many such oils tend to leave sticky residues over time, which can cause damage to the oil pump or other parts. 325” - D DES 300, 350, 400 DES 380 Use a special round file for chains for sharpening the chain. Turn over after a certain period of time so that the bearing surfaces are uniformly worn. 15 11 13-14 14 14 Sprocket Chain brake Each time before putting the saw into operation Saw chain Guide bar Chain lubrication Chain brake Power switch Power supply cable Oil tank cap After each shutdown Chain brake Guide bar Chain carrier Chain oil tank Saw chain/guide bar Electric chain saw 12 14 14 13 Storage Service, spare parts and guarantee Maintenance and repair The maintenance and repair work of modern electric motors as well as all safety related assemblies require qualified technical training and the availability of a special workshop equipped with special tools and testing devices. 17 Guarantee MAKITA guarantees the highest quality and will therefore reimburse all costs for mending through replacement of damaged parts as a result of material or production faults, which occur within the guarantee time after purchase. We ask for your understanding that we cannot accept any responsibility for damage caused by: • Disregard of the instruction manual. For performance of repairs and for replacement of other components your MAKITA service centre should be consulted. Fastening nut Sprocket guard with brake Sprocket nose bar 30 cm (12") Sprocket nose bar 35 cm (14") Sprocket nose bar 40 cm (16") Sprocket nose bar 38 cm (15”) Saw chain 3/8", 30 cm Saw chain 3/8", 35 cm Saw chain 3/8", 40 cm Saw chain . - 6 - 7 - - - 8 - q q q q q q q 9 panne entretien remplissage d’huile affûtage de la chaîne pause transport mise hors service Comportement et technique de travail - 22 10 - - - - - Tenir la tronçonneuse électrique de façon qu’aucune partie du corps se trouve dans la gamme de basculement rallongée de la chaîne (11). Dans le cas contraire, tirez le protègemains (A/2) dans le sens de la flèche jusqu’au déclic. Tourner la vis de serrage de la chaîne (C/6) dans le sens contraire des aiguilles jusqu’à ce que le tourillon (C/7) se trouve face à la butée de gauche. Cet agent adhésif évite que l’huile soit jetée trop vite du dispositif de tronçonnage. [. . . ] 2 cm in de richting van de pijl kan worden getrokken, dan staat de kettingrem reeds vrij. Is dit niet het geval, dan de handbeschermer (A/2) krachtig in pijlrichting trekken tot hij merkbaar inklikt. - Controle van de kettingspanning - De zaagketting is juist gespannen wanneer de zaagketting tegen de onderzijde van de zaaggeleider aanligt en de zaagketting nog gemakkelijk met de hand bewogen kan worden over de zaaggeleider. [. . . ]